KUKKO

KUKKO K-2030-10-S Set of 2 and 3 Arm Pullers with Narrow Jaws

SKU: KUKK203010S
Shipping: Free Only In the US 48 States
$823.20

Kukko K-2030-10-S Set of Two- and Three-arm Pullers w/ Narrow Jaws

This Kukko K-2030-10-S puller set is used for removing bearings, gears, discs, etc. for tight or difficult-to-access spaces. 

Description:

  • 8 in 1 kit in the tried-and-tested KUKKO-L-Boxx-System.
  • The set facilitates the assembly of eight different pulling device models through the combination of pulling jaws and extensions.
  • Flexibility assured thanks to two-arm or three-arm design.
  • Thin pulling hooks.
  • Jaw extensions.
  • Parallel pulling hooks in every position, even with full load.
  • Pulling hooks with infinitely variable adjustment on the cross-beam.
  • Optimal adjustment of the spindle to the shaft with 2-sided spindle tip (ball and tip)
  • Short and long mechanical pressure screws.
  • Milled thread treated with special coating.
  • If there is adequate free space around the part to be removed, we recommend using a 3-jaw puller.
  • Instructions on the cover.
  • Secure storage in special foam.
  • Personal KUKKO-Chip-Code

Advantage:

  • Practical package for universal use.
  • Can be installed on various pulling hooks and variable reach thanks to jaw extensions.
  • Turning the pulling hooks enables them to be used both internally and externally.
  • Suitable for pulling asymmetric workpieces.
  • 2-jaw cross-beam with hexagonal profile for good grip.
  • Spindle head band prevents the wrench from slipping off.
  • Almost all components available as replacement parts, time-saving order process thanks to numbering system.
  • Note: Pressure pads from series 600-17 are a good addition if the shaft is hollow and the spindle cannot be supported.
  • Stability support from optional series 219 clamp.
  • Complete easy-to-manage package.
  • KUKKO-L-Boxx-System compatible with systems by all common manufacturers.

Specifications:

kukko-k-2030-10-s-puller-set-specifications.jpg

Content:

  • 20-10-SP | Universal 2-jaw puller with narrow jaws, in set
  • 614250 | Mechanical pressure spindle.
  • 30-10-T | Cross-beam

Spare Parts (Sold Separately):

  • 614160 | Mechanical pressure spindle.
  • 614250 | Mechanical pressure spindle.
  • 20-10-SP | Universal 2-jaw puller with narrow jaws, in set
  • 1-91-P | 2 narrow jaws (pair)
  • 1-191-P | 2 narrow jaws (pair)
  • 1-251-P | 2 narrow jaws (pair)
  • 1-91-S | 3 narrow jaws (set)
  • 1-191-S | 3 narrow jaws (set)
  • 1-251-S | 3 narrow jaws (set)
  • 20-10-T | 2-jaw cross bar
  • 30-10-T | Cross-beam

Assembly Set For:

  • 614250 | Mechanical pressure spindle.
  • 20-10-S | Universal 2-jaw puller with narrow jaws
  • 20-10-SP | Universal 2-jaw puller with narrow jaws, in set
  • 30-10-S | Universal 3-jaw puller with narrow jaws
  • 30-10-SP | Universal 3-jaw puller with narrow jaws, in set
  • 20-10-35-S | Universal 2-jaw puller with extended, narrow jaws - NO PURCHASING ARTICLE
  • 20-10-25-S | Universal 2-jaw puller with extended, narrow jaws - NO PURCHASING ARTICLE
  • 20-10-2-S | Universal 2-jaw puller with extended, narrow jaws - NO PURCHASING ARTICLE
  • 30-10-2-S | Universal 3-jaw puller with extended, narrow jaws - NO PURCHASING ARTICLE
  • 30-10-25-S | Universal 3-jaw puller with extended, narrow jaws - NO PURCHASING ARTICLE
  • 30-10-35-S | Universal 3-jaw puller with extended, narrow jaws - NO PURCHASING ARTICLE

How It Works:

  • The part due to be removed (e.g. a gear, pulley or ball bearing) is gripped from the outside. Tightening of the pressure screw and the resulting pressure removes the part from the shaft.
  • The puller must be positioned centrally for centre shafts. If the shaft is not sitting centrally, the parts can be removed asymmetrically with pullers with parallel pulling hooks.

Safety Information:

  • The pulling hooks' sliding parts must always sit stably and fully on the cross-beam.
  • If several parts have to be removed, always follow a step-by-step process. Do not remove several parts at the same time.
  • The pulling hooks' support surfaces must always be straight and sit fully beneath the part to be removed.
  • Do not use any electrical or pneumatic servo screwdrivers or hammer drills.
  • Protective blanket required.
  • Protective goggles required.

KUKKO quality standards:

  • Quality made in Germany.
  • Strong design, high performance and long service life.
  • Self-healing corrosion protection KUKKoating for galvanized parts (WITHOUT chrom IV).
  • Safety label to ensure protection of intellectual property.
  • A tube of KUKKO special grease included for pressure spindle.

PLEASE NOTE, IMPORTANT INFORMATION:

  • MADE IN GERMANY