Kukko K-2030-10-S Set of Two- and Three-arm Pullers w/ Narrow Jaws

This Kukko K-2030-10-S puller set is used for removing bearings, gears, discs, etc. for tight or difficult-to-access spaces. 

Description:

• 8 in 1 kit in the tried-and-tested KUKKO-L-Boxx-System.
• The set facilitates the assembly of eight different pulling device models through the combination of pulling jaws and extensions.
• Flexibility assured thanks to two-arm or three-arm design.
• Thin pulling hooks.
• Jaw extensions.
• Parallel pulling hooks in every position, even with full load.
• Pulling hooks with infinitely variable adjustment on the cross-beam.
• Optimal adjustment of the spindle to the shaft with 2-sided spindle tip (ball and tip)
• Short and long mechanical pressure screws.
• Milled thread treated with special coating.
• If there is adequate free space around the part to be removed, we recommend using a 3-jaw puller.
• Instructions on the cover.
• Secure storage in special foam.
• Personal KUKKO-Chip-Code

Advantage:

• Practical package for universal use.
• Can be installed on various pulling hooks and variable reach thanks to jaw extensions.
• Turning the pulling hooks enables them to be used both internally and externally.
• Suitable for pulling asymmetric workpieces.
• 2-jaw cross-beam with hexagonal profile for good grip.
• Spindle head band prevents the wrench from slipping off.
• Almost all components available as replacement parts, time-saving order process thanks to numbering system.
• Note: Pressure pads from series 600-17 are a good addition if the shaft is hollow and the spindle cannot be supported.
• Stability support from optional series 219 clamp.
• Complete easy-to-manage package.
• KUKKO-L-Boxx-System compatible with systems by all common manufacturers.

Specifications:

Content:

• 20-10-SP | Universal 2-jaw puller with narrow jaws, in set
• 614250 | Mechanical pressure spindle.
• 30-10-T | Cross-beam

Spare Parts (Sold Separately):

• 614160 | Mechanical pressure spindle.
• 614250 | Mechanical pressure spindle.
• 20-10-SP | Universal 2-jaw puller with narrow jaws, in set
• 1-91-P | 2 narrow jaws (pair)
• 1-191-P | 2 narrow jaws (pair)
• 1-251-P | 2 narrow jaws (pair)
• 1-91-S | 3 narrow jaws (set)
• 1-191-S | 3 narrow jaws (set)
• 1-251-S | 3 narrow jaws (set)
• 20-10-T | 2-jaw cross bar
• 30-10-T | Cross-beam

Assembly Set For:

• 614250 | Mechanical pressure spindle.
• 20-10-S | Universal 2-jaw puller with narrow jaws
• 20-10-SP | Universal 2-jaw puller with narrow jaws, in set
• 30-10-S | Universal 3-jaw puller with narrow jaws
• 30-10-SP | Universal 3-jaw puller with narrow jaws, in set
• 20-10-35-S | Universal 2-jaw puller with extended, narrow jaws - NO PURCHASING ARTICLE
• 20-10-25-S | Universal 2-jaw puller with extended, narrow jaws - NO PURCHASING ARTICLE
• 20-10-2-S | Universal 2-jaw puller with extended, narrow jaws - NO PURCHASING ARTICLE
• 30-10-2-S | Universal 3-jaw puller with extended, narrow jaws - NO PURCHASING ARTICLE
• 30-10-25-S | Universal 3-jaw puller with extended, narrow jaws - NO PURCHASING ARTICLE
• 30-10-35-S | Universal 3-jaw puller with extended, narrow jaws - NO PURCHASING ARTICLE

How It Works:

• The part due to be removed (e.g. a gear, pulley or ball bearing) is gripped from the outside. Tightening of the pressure screw and the resulting pressure removes the part from the shaft.
• The puller must be positioned centrally for centre shafts. If the shaft is not sitting centrally, the parts can be removed asymmetrically with pullers with parallel pulling hooks.

Safety Information:

• The pulling hooks' sliding parts must always sit stably and fully on the cross-beam.
• If several parts have to be removed, always follow a step-by-step process. Do not remove several parts at the same time.
• The pulling hooks' support surfaces must always be straight and sit fully beneath the part to be removed.
• Do not use any electrical or pneumatic servo screwdrivers or hammer drills.
• Protective blanket required.
• Protective goggles required.

KUKKO quality standards:

• Quality made in Germany.
• Strong design, high performance and long service life.
• Self-healing corrosion protection KUKKoating for galvanized parts (WITHOUT chrom IV).
• Safety label to ensure protection of intellectual property.
• A tube of KUKKO special grease included for pressure spindle.

PLEASE NOTE, IMPORTANT INFORMATION:

• MADE IN GERMANY